?output signals: each signal within range from 4 to 20 ma dc non-isolated (isolated output available at option) co instantaneous value o 2 instantaneous value co instantaneous value after o 2 correc- tion 1-hour moving average co value after o 2 correction moving average co value after o 2 cor- rection (averaging time variable) time setting in 1 to 59 minutes (1-minute increment) or 1 to 4 hours (1-hour incre- ment) allowable load resistance 550 ? or less ?contact output: 1a no-voltage contact (contact capacity 250 v ac, 2 a) peak count alarm, co instantaneous value upper limit alarm, auto calibration and maintenance statuses, calibration er- ror, analyzing block error and range dis- crimination ?contact input: no-voltage contact (on/0v, off/5 v dc, dc 5ma at on) auto calibration remote start (for 500 msec or longer), remote range changeover remote average value resetting (for 500 msec or longer) ?indication: lcd with back light for indicating co in- stantaneous value, o 2 instantaneous value, co instantaneous value after o 2 correction and co average values after o 2 correction (1-hour and time-variable averagings), peak count value and param- eter assignment ?measuring system: non-dispersive infrared absorption (ndir) method for co zirconia method for o 2 ?measurable component and range: co ; 0~200/500ppm 0~200/1000ppm 0~500/1000ppm 0~500/2000ppm o 2 ; 0~25vol% ?repeatability: 0.5% of full scale ?zero drift: max. 2.0% of full scale/week for co max. 2.0% of full scale/month for o 2 ?span drift: max. 2.0% of full scale/week ?linearity: max. 1.0% of full scale ?sample gas extracting rate: approx. 2 r /min ?response time: within 90 seconds for 90% indication (af- ter extracting sample gas through the inlet) ?warm-up time: within 4 hours after power-on this instrument is equipped with a non-dispersive infrared co sensor and a zirconia o 2 sensor. it is used for measur- ing co and o 2 in the gas emitted from a garbage incinera- tor to meet japanese regulation on emission control of dioxins (tetrachlorodibenzoparadioxins). co instantaneous value, o 2 instantaneous value, co instan- taneous value after o 2 correction and co average values after o 2 correction (1-hour and time-variable averagings) can be output, and a peak count/alarm function is incorporated. specifications features data sheet zs q co/o 2 gas analyzer for stack gas 1. suitable functions for emission control of dioxins. output includes co instantaneous value, o 2 instantaneous value, co instantaneous value after o 2 correction and co average values after o 2 correction (1-hour and time- variable averagings). count/alarm function against excess over specified value 2. space-saving configuration by unitizing the analyzer and sampling device into 19-inch types. 3. easy to maintain with auto calibration and with ?rom the front maintenance construction? 4. a microjet recorder (fuji electric? type phc or phe) can be built in for recording measured gas concentration and temperature values. date EDS3-116E jun. 30, 2011
zs q 2 ?standard requirements for sample gas: ?temperature; 60 to 800?c ?dust; 100 mg/nm 3 or less ?pressure; ?.94 to +2.94kpa {?00 to +300mmh 2 o} ?components; so 2 500 ppm or less nox 1000 ppm or less co 2 0 to 15% co 0 to 2000 ppm o 2 0 to 21% hc r 1000 ppm or less n 2 , h 2 o remaining per- cent ?rated operating conditions: ?ambient temperature; ? to +40?c ?ambient humidity; 90% rh or less ?power supply voltage; 100 v ac 10 v ?power supply frequency; 50 or 60 hz 0.5 hz ?power consumption; max. 400 va (without gas extractor) ?installation requirements: 1) selection of a place which does not receive direct sunlight or radiation from hot substances 2) avoidance of a place under heavy vi- bration 3) clean atmospheric air ?external dimensions (h x w x d): indoor type 1550 x 735 x 650 mm outdoor type 1640 x 745 x 765 mm ?mass: approx. 140 kg (excluding standard gas) ?cubicle finish color: munsell 5y7/1 semi-gloss ?other: three standard gas (3.4 r ) cylinders accommodable ?recorder (option): 100 mm-width recorder (fuji electric? type phc or phe) built in, max. 6 points recordable ?gas extractor: electrical heating type (filter built in) filter mesh; 40 m mesh of sus 316 stainless steel probe; sus 316 stainless steel of 300, 400, 600 or 800 mm length flange; jis 5k65aff mass; approx. 9 kg ?sample inlet tube: 10/ 8 teflon tube or heating tube (max. 30 m) ?functions: 1) o 2 correction conversion of measured co gas concentration into a value at standard o 2 concentration c; co concentration after o 2 correction c s ; measured co concentration o s ; measured o 2 concentration (%) o n ; standard o 2 concentration (12% for garbage incinerator) 2) auto calibration auto calibration cycle settable range: 1 to 99 hours (1- hour step) or 1 to 40 days (1-day step) auto calibration gas flow time settable range: 60 to 599 seconds (1-sec step) auto/manual calibration error contact output: provided when calibration quantity exceeds 50% of full scale. contact output during auto calibration and maintenance: provided during calibration gas flow and replacement. also provided during maintenance. auto calibration remote start contact input: calibration starts by opening and closing the contact input of 500 msec or longer in duration. 3) output holding function output signal is held during auto calibration and mainte- nance. 4) alarm 1 co instantaneous value upper limit alarm 2 co instantaneous value peak count alarm is issued and indicated when co instantaneous value has exceeded the set upper limit by the set number of times. (settable number of times: 1 to 99, settable value range: 0 to 1000 ppm) 5) other functions remote range changeover input: low range is selected when closing the contact input, and high range is se- lected when opening the contact input average value resetting input: the output and indication of co average value after o 2 correction is reset by open- ing the contact after the contact is closed for 1.5 sec or longer. ? ange discrimination contact output: contact closed for low range analyzing block error contact output: temperature input signal: k thermocouple input x 2 (in- put for recorder) c s (21 ? o n ) 21 ? o s calculating equation: c = ?gas analyzer system ?specified external drain separator ?specified gas extractor/probe set ?specified gas inlet tube set ?specified standard gas set (with pressure reducing valve) ?specified recorder to be accommodated in cubicle ?standard accessory set scope of delivery 1. code symbols 2. necessity of spares for 1-year measurement 3. type of recorder (option) 4. anchor bolt ordering information
3 - 4 1 q s z 2 1345 678 - 10 9111213 15 14 16 17 description power supply (6th code) ac 100v 50hz ac 100v 60hz ac 115v 60hz ac 230v 50hz measurement range (5th code) 0~200 / 500 ppmco 0~25% o 2 0~200 / 1000 ppmco 0~25% o 2 0~500 / 1000 ppmco 0~25% o 2 0~500 / 2000 ppmco 0~25% o 2 (note 1) specify this code when the downward inclination of the sample inlet tube from the gas extraction point to the analyzer gas inlet is less than 15?, or when the water contents at the gas extraction point exceed 30 vol%. (note 2) recorder assignment is as follows. in 6-point recording: in 2-point recording: ch1; co instantaneous value ch1; co instantaneous value ch2; o 2 instantaneous value ch2; o 2 instantaneous value ch3; co instantaneous value after o 2 correction ch4; 1-hour average co value after o 2 correction ch5; k thermocouple 1 ch6; k thermocouple 2 a b c d cubicle structure (7th code) indoor type outdoor type indoor type outdoor type specify when installation place is at ??c or lower (?0?c min.) a b c d 3 4 6 7 recorder (11th code) not provided with 6-point recorder phc with 2-point recorder phe y c e isolated output (12th code) non-isolated output isolated output (5 outputs) 0 5 jpapn quality assurance organization test (13th code) no yes (test of individual products needs to be ordered separately.) 0 1 standard gas (14th code) not provided (space for accommodating three 3.4 r cylinders of air + o 2 /n 2 + co/n 2 ) not provided (space for accommodating two 3.4 r cylinders of o 2 /n 2 + co/n 2 ) air + o 2 /n 2 + co/n 2 (3.4 r , 3 cylinders)(incorporated) with official organization's test o 2 /n 2 + co/n 2 (3.4 r , 2 cylinders)(incorporated) air + o 2 /n 2 + co/n 2 (3.4 r , 3 cylinders)(incorporated) 1 2 3 4 5 gas extractor flange size (15th code) without gas extractor jis 5k 65a y a gas extractor insertion length (16th code) without gas extractor 300mm 400mm 600mm 800mm y a b c d sample inlet tube type length (17th code) not provided not provided 10/ 8 teflon tube 5m 10/ 8 teflon tube 10m 10/ 8 teflon tube 15m 10/ 8 teflon tube 20m 10/ 8 teflon tube 25m 10/ 8 teflon tube 30m heating tube 10m heating tube 15m heating tube 20m heating tube 25m heating tube 30m y a b c d e f g h j k l gas pressure at extraction point (9th code) ?0.98~+4.90kpa {?100~+500mmh 2 o} ?2.94~+2.94kpa {?300~+300mmh 2 o} ?4.90~+0.98kpa {?500~+100mmh 2 o} 1 2 3 external drain separator (10th code) not provided provided (note 1) y a (note 2) (recorder hardware needs to be prepared separately.) specify when the ambient temperature may fall to ??c or lower (?0?c at the lowest level). code symbols
zs q 4 ?standard gas: reference gas used for calibrating zero and span of the analyzer; air and co for span, and o 2 for zero. ?zirconia o 2 sensor: zirconia oxygen sensor used for measur- ing the oxygen concentration (0 to 25%) in sample gas. ?solenoid valve for atmospheric air: can be built in for using the atmospheric air instead of standard air. ?gas extractor: gas extraction, with heating type stain- less steel filter having a standard diam- eter of 40 m ?gas conditioner: for separation of drain, prevention of drain from being sucked through second- ary filter and composite operation of con- stant-pressure bubbler. ?gas aspirator: for aspiration of sample gas (sample gas flow rate approx. 2 r /min). ?sampling module: incorporates electronic gas cooler, sole- noid valve, membrane filter and flowme- ter. electronic gas cooler; dries the moisture in sample gas to a dew point of approx. 2?c. solenoid valve; used for introducing calibration gas. membrane filter; glass fiber and ptfe filter used to elimi- nate fine dust particles and permit monitoring of dust adhering condition on the front panel of the gas analyzer. flowmeter; adjusts and monitors the flow rate of sample gas. gas extractor gas inlet tube 15? min. sample gas inlet, 10/ 8 joint (rc 3/8) gas aspirator solenoid valve gas conditioner gas outlet drain sampling module electronic gas cooler flowmeter membrane filter o 2 /n 2 standard gas (3.4 r ) air zero span 2 co /n 2 span 1 solenoid valve pressure reducing valve note 1: solenoid valve for using atmospheric air as zero gas note 2: unnecessary when atmospheric air is used as zero gas zirconia o 2 sensor infrared gas sensor (note 1) (note 2) o 2 gas sampling system diagram co functions of individual components
5 when equipped with gas extractor no. name quantity type/part no. 1 filter paper for membrane filter/as spare tk7h6750p1 2 sheets 2 filter paper for membrane filter/as spare tk700735p3 2 sheets 3 fuse (2a)/as spare 75718n9 2 fuses 4 fuse (3.2a)/as spare 75718n10 2 fuses 9 water bottle for injection into gas conditioner tk7h3493p1 1 10 gas extractor flange packing tk7h4240p1 1 sheet 11 gas extractor fastening bolt and nut 1 set 12 o-ring (g50) for gas extractor/as spare 1 13 heating tube support tk7n0820c1 1 set (only when the heating tube has been specified) 14 instruction manual inz-tn4zsq 1 copy 5 standard gas joint r1/4 6 tk7m6047p1 3 joints (2 pieces for using only 2 standard gases) 6 hose band for fixing standard gas cylinder tk7m2005p2 12bands (8 pieces for using only 2 standard gases) 7 toalon tube for standard gas connection, 0.45 m and 9/ 5 tk727528p1 1 tube 8 polyethylene tube for standard gas connection, 5 m and 6/ 4 415966p4 1 tube standard accessories spare parts for 1-year measurement type: zbnisq12 (without gas extractor) type: zbnisq42 (with gas extractor) contents ?25-sheet filter paper for membrane filter 1 ?2-sheet filter paper for membrane filter 1 ?membrane filter o-ring (p49) 2 ?membrane filter o-ring (p3) 2 ?fuse (2 a) 3 ?fuse (3.2 a) 4 ?filter for gas conditioner 2 ?o-ring (g65) for gas conditioner 2 ?diaphragm for gas aspirator 1 ?valve for gas aspirator 1 ?fixed restrictor ( 1) 1 ?fixed restrictor ( 1.4) 1 ?o-ring (g50) for gas extractor 1 ?o-ring (g45) for gas extractor 1 ?packing for gas extractor mesh filter 1 ?mesh filter for gas extractor 1
zs q 6 connection diagram 1 + 2 3 4 5 6 7 8 9 10 11 12 100 v ac main power supply ground gas extractor power supply heating tube power supply temperature input 1 (option) temperature input 2 (option) contact output, range discrimination signal (co) + 1 + + + + + 2 3 4 5 6 7 8 9 10 analog output (1-hour average co value after o 2 correction) analog output, average co value after o 2 correction (averaging time variable) analog output, co instantaneous value after o 2 correction analog output, o 2 instantaneous value analog output, co instantaneous value 11 + ? + + + 12 13 14 15 16 17 18 19 20 1 2 3 4 5 6 7 8 9 10 + contact input, average value resetting notes: 1. connection to the parenthesized terminals has already been made. 2. avoid connection to the terminals for internal connection. contact input, auto calibration remote start (output holding during maintenance) for internal connection contact input, remote range (co) + + + + analog input, o 2 sensor (for internal connection) (for internal connection) 11 12 13 14 15 16 17 18 19 20 1 2 3 4 5 6 7 8 9 10 (m3.5 screw) (m3.5 screw) (m4 screw) (m4 screw) (m3.5 screw) contact output, analyzing block error for internal connection contact output, calibration error contact output, pump on/off contact output, auto calibration status and maintenance status contact output, for atmospheric a ir solenoid valve 11 12 13 14 15 16 17 18 19 20 1 2 3 4 5 6 7 8 9 10 + for internal connection contact output, upper limit alarm (co) contact output, peak count alarm analog output, 1-hour average co value after o 2 correction analog output, co average value after o 2 correction (averaging time variable) analog output, co instantaneous value after o 2 correction analog output, o 2 instantaneous value analog output, co instantaneous value terminal block 1 terminal block tb1 terminal block tb2 (option for isolated output) terminal block 3 terminal block 2 outline diagram (unit: mm) left side view front view anchor plan and door opening diagram front side rear side anchor bolt 420 1450 1550 610 650 drain, gas outlet (rc 1 / 4 ) 3 wiring ports with 34 grommet 4- 15 600 (135) 100 420 610 32 35 door (4-m12 160 50) (option) 765 (for outdoor installation) for outdoor installation gas conditioner 615 sample gas inlet (with joint for 10/ 8 tube) (rc 3 / 8 ) 1640 (for outdoor installation)
7 outline diagram (unit: mm) heating tube support (added for heating tube specifications) up (750) 357 212 293 27 130 155 (76) f 155 pl name plate handle exchange filter cable hole g1/2 name plate sampling pipe 20a by order rc3/4 flange jis 5k 65a ff 4- 15 cover rc1/2 gas outlet with joint for 10/ 8 te r minal box gas inlet
zs q printed in japan caution on safety *before using this product, be sure to read its instruction manual in advance. international sales div sales group gate city ohsaki, east tower, 11-2, osaki 1-chome, shinagawa-ku, tokyo 141-0032, japan http://www.fujielectric.com phone: 81-3-5435-7280, 7281 fax: 81-3-5435-7425 http://www .fjielectric.com/products/instruments/ information in this catalog is subject to change without notice.
|
